[Patrick] decided to make a computer controlled etch-a-sketch. While the idea is not that new, there is always a different way to accomplish a goal. An Arduino is used to control a pair of stepper motors which were sourced for pretty cheap, and even came with their own driver. Next a stand was mocked up using foam board, which helps determine where all the parts should live.

Next was a way to attach the steppers to the knobs, gears would be used and a collet meant for model airplanes was sourced to make the mechanical connection between gear and shaft. With everything set in place via foam board and paper printouts, it is off to get some thin plywood. The plywood is sent though a laser cutter creating most of the stand and gears. Now its all software, a program was whipped up for OSX which converts low res pictures into squiggly lines perfect for the etch-a-sketch to draw on its screen.

The results are quite impressive, join us after the break for a quick video.

Moneycontrol.com

TRAI to step-in to address tariff woes, says MNP's the way
Moneycontrol.com
Yesterday, the SC got many heads turning after it revoked the licenses of some 122 telecom companies operating in the country. Just recently, reports also confirmed that cash-strapped telcos were looking at tariff hikes as the way out of the current …
Ruling has some subscribers worriedHindu Business Line
No adverse impact on FDI: JS Sharma, TRAI ChairmanEconomic Times
No first come licence issuance: TRAIindiablooms
The Asian Age -The Nation
all 11 news articles »

]]> http://clickmoviez.com/uncategorized/trai-to-step-in-to-address-tariff-woes-says-mnps-the-way-moneycontrol-com/22164/feed 0 http://clickmoviez.com/uncategorized/how-do-i-find-a-good-tax-professional-ask-lifehacker/22050 http://clickmoviez.com/uncategorized/how-do-i-find-a-good-tax-professional-ask-lifehacker/22050#comments Thu, 02 Feb 2012 18:00:00 +0000 admin http://clickmoviez.com/?guid=4812e408ba21ce6aa1f30a8952215435 Continue reading →]]>

Dear Lifehacker, More »

[Cameron] decided to give his twenty-year-old headlamp a makeover. He uses it when he’s out for a run and wanted to have more light to see where he’s going, as well as a red tail light on the back. The stock design uses an incandescent bulb on the front of the head band, and a battery pack on the back. He managed to convert the device to output 700 lumens without major changes to the form factor of the unit.

The first change he decided on is to use a Cree XLamp which provides the 700 lumens of light by drawing about 9.5 Watts of power. Obviously the original battery pack isn’t going to do well under that kind of load, so he also sourced a 5000 mAh Lithium battery. A bit of circuit design and PCB layout gives him two driver chips for the four-element LED module, a charging circuit for the battery, and an ATtiny13 to drive the head lamp and flash the red LED tail light. See the blinky goodness in the video after the break.

That’s a lot of light, but we wonder if he experiences a warm forehead from the heat sink used to keep that LED package cool?

The Syma S107 IR is a popular little remote controlled helicopter. When a friend of [Michael]‘s started flying one around the office he decided to try and jam the signal, creating a no fly zone. Luckily some people on the internet have already decoded the IR signals used by the flying menace. From there, a quick browsing of Mouser to source some LEDs, and to whip up some code for a TI MSP430 was all that was left.

The software on the micro controller is set to broadcast a “thrust off” signal, but [Michael] admits he is not 100% sure if the helicopter is actually receiving that, or if the signal from the no fly zone is mixing with the remote’s signal, causing garbage to be received. Either way when the helicopter gets in range of the no fly zone pad it drops from the air.

Things didn’t go perfectly though, overestimating the current capabilities of the MSP was causing the micro controller to reset and crash the debugger. But a simple rearrangement of how the signals are sent quickly solved this problem.

Join us after the break for a quick video.

Confronted with the issue of finding a use for his mounting pile of junk electronics, [Rue] set out to build a persistence of vision device using a hardware state machine. We have a suspicion that his original link may go down if there’s too much traffic so here’s a cached link just in case.

Any board that is MSC-51 or MCS-48 based would have worked for his purposes. This is because the addressing scheme of the hardware makes it an easy hack. The image above shows him cutting off the processor from this board. It was chosen because of a 74HC373; it was a mistake at first but since it’s pin compatible with the 74HC374 that he needed a simple swap did the trick. From there a clock source was added, and the address information necessary to display the message was burned into an EEPROM.

Step twelve of his writeup shows a Morse Code message created by attaching the board to a broomstick and twirling it around in an arc. We took  just a minute to decode the message and believe it’s a shout-out to Hackaday. Nice, thanks for reading [Rue]!